The Foundation of Plumbing Skills When Installing a Bathtub
The Foundation of Plumbing Skills When Installing a Bathtub
Blog Article
We have stumbled upon this great article pertaining to How to Install a Bathtub listed below on the net and accepted it made good sense to talk about it with you on this page.
Installing a bathtub isn't exactly brain surgery, but it does require strong plumbing, carpentry, and often, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably difficult job. If the old tub is readily easily accessible, the job can relocate easily; if you have to open a wall surface to remove the old bathtub as well as position the new bathtub, the task is much harder. In either instance, the job is within a home handyman's skills, although you will require a helper to leave the old bathtub and also embeded in the new one. See to it you have actually certified on your own for the job and also are comfortable attempting it. Instead of employing a contractor to take control of a halfway-completed task, it is far better to take into consideration utilizing one prior to you begin. Chances are you might need an expert plumber to make tube connections.
This write-up will help you install a brand-new bathtub in your restroom if you have actually currently gotten a brand-new bathtub and also do not need to change the arrangement of your previous supply of water pipes.
Your tools as well as material checklist need to consist of the following:
Preparing for the Installment
To start with, the sustaining framework supplied with the bath needs to be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps unit to stop strain on the bath tub.
Fit the versatile faucet connectors to the bottom of both taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you utilize all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its final setting.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the water supply. After doing so, activate the faucets to drain any kind of water staying in the system. The procedure of removing the existing taps can be fairly bothersome due to the limited access that is frequently the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a towel ready for the continuing to be water that will come from the pipelines. When the supply pipelines have been removed, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from transforming during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Before moving on to fit the brand-new faucets, compare the pipe connections on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Bathtub
Using both wood boards under its feet, place the bath tub in the required setting. The wooden boards are practical in equally spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 tiny points.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level as well as changing the feet on the bathtub up until the spirit level reviews degree.
To set up taps, fit all-time low of the furthest flexible faucet port to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water and also inspect all joints as well as brand-new pipework for leaks as well as tighten them if needed. Fill the bathtub as well as additionally inspect the overflow outlet and the typical electrical outlet for leakages.
Finally, take care of the bath paneling as explained in the maker's instruction manual. Tiling and sealing around the bath tub needs to wait till the tub has actually been made use of a minimum of when as this will resolve it into its last setting.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, then you will call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin ensuring that the washing machines remain in location in between the tap and also the sink. Protect the tap in place with the supplier given backnut. When the tap is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet connectors. The former kind must be linked to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to split a rigid seal, causing the water to pass through the wall in between the bathroom as well as the tiling, resulting in issues with moisture and also possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes and also cartridges, and also are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched paper or soft rope. Remember to always load the tub with water before sealing, to allow for the activity experienced when the tub is in usage. The sealant can fracture fairly early if you do not take into consideration this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently offered on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed our topic about How to Install a Bathtub. Thank you so much for taking a few minutes to read our blog. Loved our blog posting? Please share it. Let other people locate it. I praise you for your time. Please stop by our blog back soon.
Hire A Pro Report this page